I spent this morning at Willard slow trolling Fligs for catfish. One rod had an Ambassadeur 6600 with the clicker, the other was a spinning outfit. Both worked, each accounting for 2 fish. The Ambassadeur requires little attention, simply wait until it sings, however I wonder how many fish drop the bait before I can reach it. The spinning reel is the opposite and requires constant monitoring. I looked away long enough for a course adjustment and when I turned around the rod was bent to the water and the drag was running away, unfortunately this fish carried a hook remover.
So I was wondering how many folks prefer a clicker or not.
I did learn one important lesson today, cut the spines off before you toss kitty’s into the livewell. Trying to remove the drain plug from a livewell full of hyper active catfish is like playing fully automatic dodgeball, it sounds like fun but it really isn’t.
I spent the morning on Willard as well, I did not manage to get any fish to the boat. Had a few hits and one that took a bit of drag before spitting out the circle hook. I was in a kayak started out from Pelican beach and made it down through most of freeway bay. This was my first time using a worm rig that had a floating spinner. Not quite a flig setup, but not sure the best way to fish it. I had a bottom bouncer and this rig trailing about 20”
I’m with TD. When I started fishing for cats 2 years ago I bought a couple of reels with clickers. I soon learned that with circle hooks it was better for the fish to have the line anchored so the hook can turn and set in their mouths. As I evolved as a catman I’ve started to do like TD said and sometimes adjust my drag so that the fish have the resistance that sets the hook but they can also run with it a bit. But if you want to stay traditional I can tell you what BLK does. Sometimes he holds the line between his thumb and forefinger. I guess he can feel the lightest bite and react accordingly. As a side note, I’ve only fished Willard once, going for wipers. Ended up catching two cats on the wiper lures. Go figure. They certainly didn’t need a hookset.
I’ve used TDs big fligs a lot this year because they just plain work. Those sickle hooks are great. Only problem is that once in a while they swallow them and I end up having to take them home to eat and retrieve the lures. I bought some long-reach pliers with a bent tip to see if I could reach in and get the flig out of their gullet. Wouldn’t you know it, I haven’t had a deep hook since so I don’t know how they work. The real trick is to grab the hook behind the flig body so you don’t rip it up.
Where do I find fligs at? Or how to make them.
Pat,
I would like to see your painting technique one day, maybe when it starts getting cold outside.
What are you using to make the silver look like chrome? I have CS vinyl paint and the silver looks opaque.
I second your belief in sharp hooks, they are the cheapest part of fishing and the worst place to pinch pennies.
Along with marabou I use Arctic fox tail, bucktail, and dyed wool. Stiff synthetics like supreme hair are durable but I think they could interfere with a fish sucking in the bait.
JArner,
Pat has an excellent tutorial on flig making. If you want I would be happy to show you my technique, its quick but does require a drill and belt sander.
Thanks, I’d be happy to have either or in fact both tutorials. I’ve got a drill and could pick up a belt sander. I’ve been looking at the EPS method that uses jig molds, but none of the molds I’ve seen really offer what I want. Since they have mostly been designed around lead based pours.
This is a quick look at how I shape the bodies.
First I make a pilot hole with a sewing awl, the closer to center the better.
Then I slide the foam over a bamboo skewer chucked in a drill.
Running the drill in reverse so the foam and sanding belt are moving in opposite directions I start by sanding a taper on the front .
Then I sand the rear taper
And lastly I round off the middle section. Of course, all of this assumes that you obtained a foam kneeling pad and cut the plugs with some sort of hole saw, I use a .458 winchester magnum case with the mouth sharpened.
TubeDudes tutorial goes into much more detail, including foam selection, cutting, painting, and gluing the body onto the hooks so there isn’t any need for me to repeat it.
If I did this correctly, this should be TubeDudes complete tutorial.
Everything is there if you click on the photos