05-28-2003, 06:01 AM
[font "Arial"][size 2]Welcome to BFT message board. I still have lots of blowups with Baitcasters but hope this help you. First Baitcaster reels have mechanisms built into the reel that allow you to control the spool speed and reduce the amount of overruns. But the single most effective spool control method is your thumb! Basically getting the most out of your baitcaster is a matter of thumb education. During the cast you should keep your thumb near the spool. If you think the cast is going too fast or is heading for the trees you can stop it immediately with your thumb. You can also start to feel an overrun happening as the loops of line start to form you can feel them with your thumb and do something about it. And most importantly you can stop the spool spinning as soon as the line hits the water. I have found when casting if I stop the spool with my thumb just before the bait hits the water I have less overruns. As you get better and better at this you can also use your thumb to fine tune the spool during a cast and get your bait or lure right into the correct place.
Most good baitcaster reels have two mechanisms to control the spin rate of the spool. They are usually called something like magnetic or friction cast control and centrifugal brake system. Fancy names but simple to operate. The magnetic cast control is usually a round knob on the same side of the reel as the drag and the handle. This knob is tightened or loosened to retard the spinning of the spool. You can modify this setting while you are fishing. You usually have to change this as the weight of what you are casting changes. A heavier casting weight will make the spool spin much quicker at the beginning of the cast. You need this knob to stop the spool spinning out of control. The lighter the weight the less control you need. If it is too tight you may find the weight in your cast is insufficient to get the spool spinning at all.
The centrifugal brake system on baitcasters most have two. Some are on the side of the reel and can be modify when fishing. Most are numbers from one thru ten start on ten and work down until you get the right number for the bait you are using. You will know when it gets on the right number. But some centrifugal brake system are found inside the reel. You have to pull the reel apart to make changes here. Be warned most baitcaster have a lot of springs and internal parts. I would not recommend taking them apart. The brakes are usually on the opposite side to the drag knob and handle. The brake system is a series of four to six knobs in a circle around the inside of the reel. These are used to provide extra control on the spool. You can start with all of these set to on and as you become more confident with your casting you can start turning these off. Both of these mechanisms reduce the speed that the spool can move, and therefore reduce the distance you can cast. As you get the hang of the reel you can start turning these off and see your casts really fly.
Your reel should include the specific instructions for the setting of both these controls.
Here are the basics steps you should use to set the magnetic cast control:
Rig up the rod with the sinkers/hooks or lure you want to cast.
Tighten the magnetic cast control knob all the way up.
Put the reel into free spool, with the rod up suspending the sinker etc.
The line should not be coming out.
Loosen the magnetic cast control knob slowly until the line will start to come out.
Be careful that it does not start to come out so fast that you get another birds nest!
Then tighten back a little way. The line should not move unless you jig the rod up and down. When you do that
the sinker etc should move down a little way.
Try casting now. If you still have overruns tighten the cast control knob.
This will give a reasonable setting for the weight you are casting. Once you get your thumb educated you should start backing this off so as not to reduce the distance you can cast.
Another thing to consider is the type of line you use when casting. A stiff line with a lot of memory will increase the number of overruns. Because these lines are not supple they stay looped up as they come off the reel. These can foul up the spool and cause overruns. Also it is much harder to get these overruns out. Probably the best line to use would be one of the braids. These have no memory and will come straight off the spool.
[center] [/center]
[/size][/font]
[signature]
Most good baitcaster reels have two mechanisms to control the spin rate of the spool. They are usually called something like magnetic or friction cast control and centrifugal brake system. Fancy names but simple to operate. The magnetic cast control is usually a round knob on the same side of the reel as the drag and the handle. This knob is tightened or loosened to retard the spinning of the spool. You can modify this setting while you are fishing. You usually have to change this as the weight of what you are casting changes. A heavier casting weight will make the spool spin much quicker at the beginning of the cast. You need this knob to stop the spool spinning out of control. The lighter the weight the less control you need. If it is too tight you may find the weight in your cast is insufficient to get the spool spinning at all.
The centrifugal brake system on baitcasters most have two. Some are on the side of the reel and can be modify when fishing. Most are numbers from one thru ten start on ten and work down until you get the right number for the bait you are using. You will know when it gets on the right number. But some centrifugal brake system are found inside the reel. You have to pull the reel apart to make changes here. Be warned most baitcaster have a lot of springs and internal parts. I would not recommend taking them apart. The brakes are usually on the opposite side to the drag knob and handle. The brake system is a series of four to six knobs in a circle around the inside of the reel. These are used to provide extra control on the spool. You can start with all of these set to on and as you become more confident with your casting you can start turning these off. Both of these mechanisms reduce the speed that the spool can move, and therefore reduce the distance you can cast. As you get the hang of the reel you can start turning these off and see your casts really fly.
Your reel should include the specific instructions for the setting of both these controls.
Here are the basics steps you should use to set the magnetic cast control:
Rig up the rod with the sinkers/hooks or lure you want to cast.
Tighten the magnetic cast control knob all the way up.
Put the reel into free spool, with the rod up suspending the sinker etc.
The line should not be coming out.
Loosen the magnetic cast control knob slowly until the line will start to come out.
Be careful that it does not start to come out so fast that you get another birds nest!
Then tighten back a little way. The line should not move unless you jig the rod up and down. When you do that
the sinker etc should move down a little way.
Try casting now. If you still have overruns tighten the cast control knob.
This will give a reasonable setting for the weight you are casting. Once you get your thumb educated you should start backing this off so as not to reduce the distance you can cast.
Another thing to consider is the type of line you use when casting. A stiff line with a lot of memory will increase the number of overruns. Because these lines are not supple they stay looped up as they come off the reel. These can foul up the spool and cause overruns. Also it is much harder to get these overruns out. Probably the best line to use would be one of the braids. These have no memory and will come straight off the spool.
[center] [/center]
[/size][/font]
[signature]